Knowledge CentrePower

How to choose a power supply for LED and display applications

Voltage, current and wattage — why all three matter, how constant-voltage supplies differ from constant-current LED drivers, and how to read an existing label.

Published

Switching power supply board

Short answer

Match the type first, then the numbers. LED strips, many LED modules and LED display boards run from a constant-voltage supply, which must match their voltage; many LED lamps and fixtures use a constant-current driver, which must match their current. Then check the power rating covers the load with headroom. Wattage alone doesn’t tell you whether a supply is compatible.

Why does the right power supply matter?

A supply that doesn’t suit the load can leave LEDs dim or flickering, overheat them and shorten their life, or shut itself down. A mismatch can also damage LEDs outright — a constant-voltage supply connected directly to LEDs that need a constant-current driver can push too much current through them.

Voltage, current and wattage: what’s the difference?

  • Voltage (V) is the electrical pressure the supply provides.
  • Current (A or mA) is how much electricity flows through the load.
  • Power (W) is the two multiplied: watts = volts × amps.

A 12 V supply delivering 2 A provides 24 W. So does a 24 V supply delivering 1 A — which is why a wattage figure on its own doesn’t describe a supply.

Constant voltage or constant current?

Constant-voltage supplies

Hold the output at a fixed voltage — 12 V or 24 V, for example — and let the load draw the current it needs, up to the supply’s limit. LED strips, many LED modules and LED display boards are designed for constant voltage.

Constant-current drivers

Hold the output at a fixed current — 700 mA or 1500 mA, for example — and let the voltage settle where the LEDs need it, within a stated range. Many LED lamps, downlights and floodlight modules use constant-current drivers.

Constant voltage and constant current compared
Constant voltageConstant current
Holds fixedVoltage (e.g. 12 V, 24 V)Current (e.g. 700 mA, 1500 mA)
Usually rated byVolts, and watts or ampsMilliamps, a voltage range, and watts
Typical loadsLED strips, modules, LED display boardsLED lamps, downlights, floodlight modules
What must matchThe load’s voltageThe load’s current, within the voltage range

A unit rated at a fixed voltage, such as the 12V 400W Driver (12 V, 400 W), is typically used as a constant-voltage supply. A unit rated in milliamps, such as the 1500mA 50W Driver (1500 mA, 50 W), is typically a constant-current driver. Confirm the output type and voltage range on the label or datasheet before connecting.

Why isn’t wattage alone enough?

Two units with the same wattage can be completely different. A 50 W, 12 V constant-voltage supply and a 50 W, 1500 mA constant-current driver are not interchangeable, even though both say 50 W.

Use wattage as the last check, not the first. Once the type, voltage and current match, make sure the power rating covers the load with headroom — a common practice is to load a supply to no more than about 70–80% of its rating. Choosing a power supply for LED display boards works through the load calculation.

How do I match the supply to the application?

  • LED display boards: low-voltage DC — check the module’s rated input (many use 5 V) and add up the load across all modules.
  • LED strips and modules: match the voltage, commonly 12 V or 24 V, and add up the watts per metre or per module.
  • LED lamps and fixtures with separate drivers: match the driver’s output current and voltage range to the LED module.
  • Outdoor or enclosed installations: choose a supply suited to the environment, and leave room for ventilation.

How do I read an existing driver or power supply label?

The label on the old unit is the best guide to a replacement. Look for:

  • Input: what it runs from — for example 100–240 V AC.
  • Output voltage: a fixed value (constant voltage) or a range (common on constant-current drivers).
  • Output current: a maximum (constant voltage) or a fixed value in mA (constant current).
  • Rated power, in watts.
  • Any markings for outdoor use or dimming.

Photograph the whole label, sharply, and note how the output is wired to the LEDs.

Replacing a driver or power supply

  1. Match the type: constant voltage or constant current.
  2. Match the output voltage — or the output current and voltage range.
  3. Check the power rating covers the load, with headroom.
  4. Check the input voltage suits your supply.
  5. Check the size, mounting and environment: indoor, outdoor or enclosed.

Don’t assume compatibility from wattage alone, and have mains connections made by a qualified electrician.

What to send for a power requirement

  • A photo of the existing label, for a replacement.
  • What it powers: LED display boards, LED strip, LED lamps or fixtures.
  • The voltage or current the load needs.
  • The total power of the load.
  • Indoor or outdoor installation.
  • The quantity.

V Bright Electronics India deals in power supplies, including the 1500mA 50W Driver and the 12V 400W Driver, and in LED display boards.

Key takeaways

  • Match the type first: constant voltage or constant current.
  • Constant voltage must match the load’s voltage; constant current, its current.
  • Watts = volts × amps — the same wattage can mean very different outputs.
  • Check the power rating last, with headroom.
  • The old unit’s label is the best guide to a replacement.

FAQ

Common questions

Have a question about a specific part? Ask us with the part number or a photo.

Ask on WhatsApp

Does wattage alone tell me if a power supply is compatible?

No. Two 50 W units can have completely different outputs. Match the type (constant voltage or constant current) and the voltage or current first, then check the wattage covers the load.

What is the difference between a constant-voltage supply and a constant-current driver?

A constant-voltage supply holds a fixed voltage, such as 12 V; a constant-current driver holds a fixed current, such as 1500 mA. The LED load is designed for one or the other.

Can I use a higher-wattage power supply?

For a constant-voltage supply, generally yes if the voltage matches — the load only draws what it needs. For a constant-current driver, the current and voltage range must match the LEDs.

What do I need to replace an LED driver?

A photo of the old driver’s label showing its output voltage, current and power, plus what it powers and where it’s installed.

Related

Products in this guide

More articles

Need a power supply or driver?

Send a photo of the existing label — or the load, voltage or current, and power — with the quantity.

Include

  • Label photo
  • Load type
  • Voltage or current
  • Power
  • Quantity