Knowledge CentreLED & Displays

How to choose the right LED display pixel pitch

Pixel pitch decides how sharp a screen looks and how close viewers can stand. A simple guide to matching P1.25 – P40 to your viewing distance.

Published

Short answer

Choose pixel pitch mainly by viewing distance. Pixel pitch is the distance between the centres of neighbouring pixels, in millimetres: the smaller the number, the closer together the pixels, and the closer viewers can stand before the picture looks dotted. A common rule of thumb puts the closest comfortable viewing distance in metres at roughly the pitch in millimetres — about 2.5 m for P2.5 and 10 m for P10.

What is pixel pitch?

Pixel pitch is the distance from the centre of one LED pixel to the centre of the next, measured in millimetres. It is written with a P: P2.5 means 2.5 mm between pixel centres, and P10 means 10 mm.

Each pixel is a group of red, green and blue LEDs, or a single package containing all three. The pitch sets how densely those pixels are packed — and with it, how much detail the screen can show.

How does pixel pitch affect sharpness?

Pitch fixes how many pixels fit into each metre of screen: divide 1,000 by the pitch. A P2.5 display has 400 pixels per metre in each direction; a P10 display has 100. For the same screen size, the smaller pitch shows four times the detail across — and sixteen times the pixels per square metre.

Pixel density by pitch
PitchPixels per metrePixels per m²Closest viewing distance (rule of thumb)
P1.25800640,000About 1.25 m
P2500250,000About 2 m
P2.5400160,000About 2.5 m
P425062,500About 4 m
P520040,000About 5 m
P812515,625About 8 m
P1010010,000About 10 m
P20502,500About 20 m
P4025625About 40 m
Pixels per metre = 1,000 ÷ pitch. Viewing distances are a rule of thumb, not a specification.

How far away will viewers be?

Viewing distance is the starting point. Up close, the eye can pick out individual pixels on a coarse pitch; farther away, they blend into a smooth picture. A widely used guideline takes the pitch in millimetres as the closest comfortable distance in metres, and puts the best viewing distance at around two to three times that figure.

  • Viewers within a few metres — shop counters, reception desks, meeting rooms: finer pitches.
  • Mixed distances — halls, auditoriums, stages and events: middle pitches, chosen for the closest seats that matter.
  • Viewers far away — building fronts, roadsides and grounds: larger pitches.

How does screen size come into it?

A screen’s resolution is its size divided by the pitch. A 3 m × 2 m screen at P2.5 is 1,200 × 800 pixels; the same screen at P10 is 300 × 200 pixels. If the content needs fine detail — small text, charts or video — it needs a smaller pitch or a larger screen.

A smaller pitch means more LEDs in every square metre, which generally raises the cost of the display. The aim is the largest pitch that still looks sharp from where people will actually stand.

Indoor or outdoor?

Indoor displays are usually seen from closer and use finer pitches. Outdoor displays are generally seen from farther away, must be bright enough to read in daylight and need protection from the weather. Where the display will be installed narrows the choice of display boards before pitch is decided.

What should I send for a display requirement?

  • The display size, or the wall area available.
  • Indoor or outdoor installation.
  • The typical and closest viewing distance.
  • What it will show — text, images or video.
  • Your preferred pitch, if you have one.
  • The project location and quantity.

V Bright Electronics India deals in LED display boards in 19 pixel pitches from P1.25 to P40. To power them, see Choosing a power supply for LED display boards.

Key takeaways

  • Pixel pitch is the distance between pixel centres, in millimetres.
  • A smaller pitch packs in more pixels and suits closer viewing.
  • Rule of thumb: the closest comfortable distance in metres is about the pitch in millimetres.
  • Screen size divided by pitch gives the resolution.
  • Share the size, viewing distance and installation for a recommendation.

FAQ

Common questions

Have a question about a specific part? Ask us with the part number or a photo.

Ask on WhatsApp

What does P10 mean on an LED display?

P10 means 10 mm between the centres of neighbouring pixels — 100 pixels in every metre of screen, in each direction.

Is a smaller pixel pitch always better?

Not necessarily. A smaller pitch packs in more pixels, which suits viewers close to the screen, but it generally costs more per square metre. Where viewers are farther away, a larger pitch looks just as sharp.

How do I calculate an LED display’s resolution?

Divide the width and height in millimetres by the pitch. A 3 m × 2 m screen at P2.5 is 3,000 ÷ 2.5 by 2,000 ÷ 2.5 — 1,200 × 800 pixels.

Which pixel pitches does V Bright offer?

LED display boards in 19 pitches: P1.25, P1.5, P1.8, P2, P2.5, P3, P3.9, P4, P4.8, P5, P6, P8, P10, P12, P16, P20, P25, P31.25, P40.

Related

Products in this guide

More articles

Planning an LED display?

Send the display size, viewing distance and installation, and we’ll help identify a suitable pixel pitch.

Include

  • Display size
  • Viewing distance
  • Indoor or outdoor
  • Preferred pitch
  • Quantity